Making Fimo Beads :: Expository Process Essays

Making Fimo bones   The Generation X population of todays society has made the wearing of bead necklaces containing fimo beads instead a fashion statement. These necklaces contain small, round, colo redness charge plate beads and otherwise intricate beads made out of incompatible colored fimo. Fimo is a synthetic material similar to modeling clay, and sewer be utilise to start out thousands on types of beads. These beads can hence be embodied into necklaces. However, to accurately describe the do of making this bearing of bead, a guileless pattern will be utilise as an example. Specifically, the fimo example depict will assume a pattern with a small, yellow tirade center surrounded by three small, squirt triangles and three small, red triangles. The following process will allow anyone without elegant ability to take a leak a simple, inexpensive fimo bead that can ulterior be used in stylish necklaces.         The first st ep in the process involves pickings a trip to a local fraud store like, A. C. Moore, or a department store such as Wal*Mart, to buy the needful supplies. For the example fimo bead, red, yellow, and green fimo must be purchased. To make a get along necklace, other colored plastic beads would have to be bought along with a spool of beading thread and a silver clasp. Also, a sharp horizontal-edged cutting tool (for example, a razor blade) and a thick, largish pin will also be required tools in the net stages of the bead making process.             Once the supplies are gathered, the bead making process is ready to begin. The fimo color that will make up the center pile in the bead (in this case, yellow) is the color that is first readied. A chip of fimo with the diameter of a quarter and the width of a pencil, is twinge off from the large slab of fimo. It is then rubbed between both hands in a poster motion until it is w arm and no longer cracks when folded in half. Then, from that small, primed piece of fimo, a smaller, nickel-sized piece is pinched and rolled on a flat surface. The fimo is rolled into a cylindrical log that is most three inches long. It is substantial to ensure that the log is not too thin, subject matter it does not intimately pull apart.Making Fimo Beads Expository Process Essays Making Fimo Beads   The Generation X population of todays society has made the wearing of beaded necklaces containing fimo beads quite a fashion statement. These necklaces contain small, round, colored plastic beads and other intricate beads made out of different colored fimo. Fimo is a synthetic material similar to modeling clay, and can be used to make thousands on types of beads. These beads can then be incorporated into necklaces. However, to accurately describe the process of making this style of bead, a simple pattern will be used as an example. Specifically, the fimo exampl e described will have a pattern with a small, yellow circular center surrounded by three small, green triangles and three small, red triangles. The following process will allow anyone without artistic ability to create a simple, inexpensive fimo bead that can later be used in stylish necklaces.         The first step in the process involves taking a trip to a local craft store like, A. C. Moore, or a department store such as Wal*Mart, to buy the necessary supplies. For the example fimo bead, red, yellow, and green fimo must be purchased. To make a complete necklace, other colored plastic beads would have to be bought along with a spool of beading thread and a silver clasp. Also, a sharp flat-edged cutting tool (for example, a razor blade) and a thick, large pin will also be necessary tools in the final stages of the bead making process.             Once the supplies are gathered, the bead making process i s ready to begin. The fimo color that will make up the center circle in the bead (in this case, yellow) is the color that is first readied. A piece of fimo with the diameter of a quarter and the width of a pencil, is pinched off from the larger slab of fimo. It is then rubbed between both hands in a circular motion until it is warm and no longer cracks when folded in half. Then, from that small, primed piece of fimo, a smaller, nickel-sized piece is pinched and rolled on a flat surface. The fimo is rolled into a cylindrical log that is approximately three inches long. It is important to ensure that the log is not too thin, meaning it does not easily pull apart.